STANDARD BITS 
    Ø 3 mm                        
    Ø 4 mm                        
    Ø 6 mm                        
    Ø 1/8" (3.18 mm)         
    OTHER Ø                     
    "BOX BITS"                  
    PARALLEL BITS            
    SPECIAL SHAPES         
   
    "GRAVO"-TYPES  
    Ø 3.18 * 105 ... 130      
    Ø 4.36 * 155 ... 185      
    
    SERVICE   
    GRINDING TIPS           
    COATING                     
    
    
    
      
    
     
    
    
    
    
    
    
    
 
 
 
 
 
 
 
 
 
 
 
 
 GV01.0300 ... GV03.0300 / GV02.0300 ... GV06.0300        Ø=3 mm.  Blank, quarter round.
Engraving bit, blank, quarter round
Solid carbide blanks, ground, one end or both ends split twice. Flats are polished.
Single end split:
GV01: Length of quarter section = 1.5 * D
GV03: Length of quarter section = 2 * D
GV05: Length of quarter section = 3 * D
(D = diameter)
Both ends split:
GV02: Length of quarter section = 1.5 * D
GV04: Length of quarter section = 2 * D
GV06: Length of quarter section = 3 * D
  GV01.0300...   GV03.0300...   GV05.0300...   GV02.0300...   GV04.0300...   GV06.0300...
Engraving bit, short halfening Engraving bit, medium halfening Engraving bit, long halfening Engraving bit, short halfening, both ends Engraving bit, medium halfening both ends Engraving bit, long halfening both ends
 Code  Code  Code  Code  Code  Code
 GV01.0300.038   GV03.0300.038   GV05.0300.038   GV02.0300.038   GV04.0300.038   - 
 GV01.0300.040   GV03.0300.040   GV05.0300.040   GV02.0300.040   GV04.0300.040   - 
 GV01.0300.050  GV03.0300.050  GV05.0300.050  GV02.0300.050  GV04.0300.050  GV06.0300.050
 GV01.0300.075  GV03.0300.075  GV05.0300.075  GV02.0300.075  GV04.0300.075  GV06.0300.075

Material: All cutters with total length 38 mm: ATX11, a sub-micrograin material used in pcb cutter industry. Unequalled toughness.

Other dimensions: K40, made in Germany, a superb material for general purposes. Other grades available on request.
How to read the code:   GH0n.0300.LLL
GH01...GH06    Type of cutter (see above)
0300   diameter (3.00 mm)
LLL   Total length of cutter

Other dimensions are available on request.

 Code

Prices Euro, VAT excl.

1-4 5+ 10+ 20+
 GV01.0300.038        
 GV01.0300.040             
 GV01.0300.050        
 GV01.0300.075        
 GV03.0300.038        
 GV03.0300.040             
 GV03.0300.050        
 GV03.0300.075        
 GV05.0300.038        
 GV05.0300.040             
 GV05.0300.050        
 GV05.0300.075        
 Code

Prices Euro, VAT excl. 

1-4 5+ 10+ 20+
 GV02.0300.038        
 GV02.0300.040             
 GV02.0300.050        
 GV02.0300.075        
 GV04.0300.038        
 GV04.0300.040             
 GV04.0300.050        
 GV04.0300.075        
 GV06.0300.050        
 GV06.0300.075        

 

 

 
Hint: Ready-to-use bits with other dimensions - or with alternative grinding specifications (i.e.for steel) - you can combine like this:
1) Raw cutter, i.e. halfened, i.e. GV03.0300.040
2) Grinding the tip, i.e. SF05.0300 (see "Grinding tips") according to client's specification like tip angle, relief angles and width.
3) Coating, if desired, i.e. CTIA.1.0300 (see "Coating").

  þ = Standard article. Always shipped within one week.  All prices are charged with German VAT(19%) if the client resides
  within the EC and has no VAT-ID number.

  You need bigger quantities? Ask for an individual offer.

 
GIS Gienger Industrie-Service • Segantinistr. 5 • CH - 8049 Zurich • Tel. / Fax +41-(0)44-341 5028 • mail: info@gis-tec.com
Warehouse EC • Weimarstr. 15 • D - 78532 Tuttlingen • Tel. +49-(0)7461-162020 • Fax 162021